Simrig Sr2 Sim Racing Motion System Simrig Sr2 Sim Racing Motion System The SIMRIG SR2 is our most powerful motion system. Equipped with industrial grade motors, a redesigned ECU, and a beefier power supply, the SIMRIG SR2 is professional grade equipment. Your number one request was increased load capacity. We listened. The SIMRIG SR2 can actuate a total load of 225 kg. This is 50 kg more than the previous version. Though powerful and accurate its footprint is small. The actuators mount directly to your rig. The ECU easily fits under your seat. The power supply can be tucked away next to your computer. The SIMRIG SR2 will enhance your rig without increasing its size too much. The motion system is accompanied by SIMRIG Control Center. This software control the motion system by interpreting the position and acceleration of the simulated vehicle. It supports all major simulation titles. Installation is plug-and-play. Attach the actuators, ECU, power supply, and emergency stop. Connect a few cables. Install the software. Then you are ready!   Mounting The SIMRIG SR2 is compatible with aluminum rigs built using 80x40, 120x40, and 160x40 mm aluminum extrusions, such as the popular Sim Lab P1-X, GT1 Evo or Trak Racer TR160 and TR180. Four 20x20 mm aluminum profiles and four plastic brackets are required to attach the SIMRIG SR2 to an aluminum rig. These are included. The four 20x20 mm aluminum profiles are mounted in pairs. Two at the front of the rig and two at the back. Each pair holds two SIMRIG SR2 actuators.  The plastic brackets are specifically designed to attach to either 80x40, 120x40, or 160x40 mm aluminum profiles. These profiles differ in height and therefore require a matching bracket. Brackets for these profiles are included in the box.   Performance The SIMRIG SR2 is powered by a 1000 W power supply -- more than enough power to react quickly to motion commands. This power supply attaches to your wall socket using a standard power cord. The system latency is negligible at only 7 milliseconds. We have optimized the software to make sure motion queues are on-time every time. The maximum load is set to 225 kg for best performance and longevity. The maximum load includes the rig, the driver, peripherals, and additional weight actuated by the SIMRIG SR2 motion system. This is 50 kg more than the SIMRIG SR1. Even with heavy 160x40 mm rigs (that weigh 65 kg) the SIMRIG SR2 can accommodate a driver, a seat, and peripherals that weigh up to 160 kg in total. Noise The sound-level of the SIMRIG SR2 is motion system is very low. A large rubber pad is attached to the bottom of each actuator. This keeps the system stationary and absorbs vibrations. Furthermore, the power supply is fan-less and the ECU fan only runs when necessary.   Power Supply The power supply will operate in any country in the world. It works with 100-240 V at 50-60 Hz.   In The Box: 4x SIMRIG SR2 Actuator 1x SIMRIG SR2 Electronic Control Unit 1x 1000W Power Supply (100-240 V at 50-60 Hz) 1x Emergency Stop 4x Actuator Cable (1m) 1x Power Cable (C13) 1x USB Cable (3m) 1x Low Voltage Power Cable (3m) 1x SIMRIG Control Center (download) Assorted hardware And mounting brackets for a 80x40, 120x40, and 160x40 rig: 4x SIMRIG SR2 Mounting Bracket for 80x40 4x SIMRIG SR2 Mounting Bracket for 120-160x40 4x Aluminium Profile 780x20x20 mm 4x Aluminium Angle Brackets 4x Profile Cover Assorted hardware Downloads: https://www.simrig.se/support/download/control-center/ Please note you will need your email address and the serial number of your SR2 which is located on the power unit. https://www.simrazer.com/imagestorage/3203.jpg


Updated 11 Dec 2022    Article 3203

Simrig Sr2 Sim Racing Motion System

The SIMRIG SR2 is our most powerful motion system. Equipped with industrial grade motors, a redesigned ECU, and a beefier power supply, the SIMRIG SR2 is professional grade equipment. Your number one request was increased load capacity. We listened. The SIMRIG SR2 can actuate a total load of 225 kg. This is 50 kg more than the previous version. Though powerful and accurate its footprint is small. The actuators mount directly to your rig. The ECU easily fits under your seat. The power supply can be tucked away next to your computer. The SIMRIG SR2 will enhance your rig without increasing its size too much. The motion system is accompanied by SIMRIG Control Center. This software control the motion system by interpreting the position and acceleration of the simulated vehicle. It supports all major simulation titles. Installation is plug-and-play. Attach the actuators, ECU, power supply, and emergency stop. Connect a few cables. Install the software. Then you are ready!   Mounting The SIMRIG SR2 is compatible with aluminum rigs built using 80x40, 120x40, and 160x40 mm aluminum extrusions, such as the popular Sim Lab P1-X, GT1 Evo or Trak Racer TR160 and TR180. Four 20x20 mm aluminum profiles and four plastic brackets are required to attach the SIMRIG SR2 to an aluminum rig. These are included. The four 20x20 mm aluminum profiles are mounted in pairs. Two at the front of the rig and two at the back. Each pair holds two SIMRIG SR2 actuators.  The plastic brackets are specifically designed to attach to either 80x40, 120x40, or 160x40 mm aluminum profiles. These profiles differ in height and therefore require a matching bracket. Brackets for these profiles are included in the box.   Performance The SIMRIG SR2 is powered by a 1000 W power supply -- more than enough power to react quickly to motion commands. This power supply attaches to your wall socket using a standard power cord. The system latency is negligible at only 7 milliseconds. We have optimized the software to make sure motion queues are on-time every time. The maximum load is set to 225 kg for best performance and longevity. The maximum load includes the rig, the driver, peripherals, and additional weight actuated by the SIMRIG SR2 motion system. This is 50 kg more than the SIMRIG SR1. Even with heavy 160x40 mm rigs (that weigh 65 kg) the SIMRIG SR2 can accommodate a driver, a seat, and peripherals that weigh up to 160 kg in total. Noise The sound-level of the SIMRIG SR2 is motion system is very low. A large rubber pad is attached to the bottom of each actuator. This keeps the system stationary and absorbs vibrations. Furthermore, the power supply is fan-less and the ECU fan only runs when necessary.   Power Supply The power supply will operate in any country in the world. It works with 100-240 V at 50-60 Hz.   In The Box: 4x SIMRIG SR2 Actuator 1x SIMRIG SR2 Electronic Control Unit 1x 1000W Power Supply (100-240 V at 50-60 Hz) 1x Emergency Stop 4x Actuator Cable (1m) 1x Power Cable (C13) 1x USB Cable (3m) 1x Low Voltage Power Cable (3m) 1x SIMRIG Control Center (download) Assorted hardware And mounting brackets for a 80x40, 120x40, and 160x40 rig: 4x SIMRIG SR2 Mounting Bracket for 80x40 4x SIMRIG SR2 Mounting Bracket for 120-160x40 4x Aluminium Profile 780x20x20 mm 4x Aluminium Angle Brackets 4x Profile Cover Assorted hardware Downloads: https://www.simrig.se/support/download/control-center/ Please note you will need your email address and the serial number of your SR2 which is located on the power unit.


Simrig Sr2 Sim Racing Motion System price comparison

Check the best prices and reviews for Simrig Sr2 Sim Racing Motion System

Kauppa Tuote Hinta Saatavuus Hintavertailu
digital-motorsports.com Simrig Sr2 Sim Racing Motion System 3350.00€ In stock digital-motorsports.com
Simrig Sr2 Sim Racing Motion System
3350.00€ In stock

Tags: Simrig Sr2 Sim Racing Motion System Motion-Systems
Page: simrig-sr2-sim-racing-motion-system

Reviews
Simrazer.com Vuorentaustantie 2, 33420 Tampere +358400856808 semfinlandoy@gmail.com Finland
Copyright Simrazer.com    Privacy policy    Terms of use    List all articles    Sitemap